Pass the API ICP Programs API-571 Questions and answers with Dumpstech

According to API RP 571 and API RP 583 (CUI-specific guidance):

“Neutron backscatter techniques are effective in detecting moisture within insulation systems, which can indicate areas of concern for corrosion under insulation (CUI).”

“This method provides non-invasive, quick identification of wet insulation without removing cladding.”

(Reference: API RP 571, Section 4.5.1 – Corrosion Under Insulation and API RP 583 – CUI Detection Techniques)

Thus, neutron backscatter is the preferred NDE method for moisture detection, making option B correct.

According to API RP 571 Section 5.1.2.6 (Carbonate Stress Corrosion Cracking - CSCC):

“The cracking is usually intergranular and is most commonly detected using wet fluorescent magnetic-particle testing (WFMT) after surface cleaning. PT may not be sensitive enough to detect fine cracks formed by this mechanism.”

Because CSCC cracks are typically surface-connected and very fine, WFMT offers the best visibility, especially after proper surface prep.

Therefore, Option D is correct.

API RP 571 states under the section Phosphoric Acid Corrosion:

“Corrosion usually occurs when the acid dries out and forms concentrated phosphoric acid deposits, which are very aggressive to carbon steel.”

“Drying or concentration occurs due to poor flow distribution or operational upsets. Localized areas may experience acid concentration due to vaporization.”

(Reference: API RP 571, Section 4.3.3.8 – Phosphoric Acid Corrosion)

Therefore, the most aggressive corrosion occurs when the acid dries out, making option D correct.

API RP 571 notes under Sour Water Corrosion:

“Localized thinning or under-deposit corrosion in sour water services is best detected by profile radiography, which provides a visual comparison of wall thickness over a length of pipe.”

“This technique is especially useful for assessing localized metal loss due to under-deposit attack or flow regime effects.”

(Reference: API RP 571, Section 4.3.2.3 – Sour Water Corrosion)

Hence, profile radiographic testing is most effective, making option B correct.

According to API RP 571 Section 5.3.2.3 (Spheroidization):

“Spheroidization is the transformation of the microstructure of carbon and low alloy steels when exposed to elevated temperatures for long durations. The rate of spheroidization depends on temperature, prior microstructure, and exposure time... The microstructure becomes less effective at carrying loads, and strength is reduced.”

Key influencing factors for the rate of spheroidization are:

Temperature (higher accelerates the process),

Microstructure (initial phase distribution and morphology).

Pressure and hydrogen partial pressure are not relevant for this transformation, nor is stress a primary driver.

Therefore, Option D (temperature and microstructure) is correct.

API RP 571 states under Chloride Stress Corrosion Cracking (Cl-SCC):

“Nickel contents above approximately 35% provide significant resistance to chloride stress corrosion cracking. Alloys such as Alloy 625 and Alloy 825 exhibit excellent resistance.”

“Austenitic stainless steels with lower nickel contents, such as 304 and 316, are more susceptible to Cl-SCC.”

Hence, option C (35%) is correct.

As per API RP 571 and further clarified in API RP 939-C:

“An arbitrary threshold of 50 ppmw H₂S in the aqueous phase is often used to define when carbon and low alloy steels become susceptible to cracking damage in wet H₂S environments.”

“Below this level, the risk of SSC, HIC, and SOHIC is considered lower, although damage has still occurred at lower concentrations depending on stress and metallurgical conditions.”

Therefore, the correct answer is option D (50 ppmw).

Hydrogen Stress Cracking (HSC) is a subclass of environmental cracking that occurs in certain materials when hydrogen is present. According to API RP 571, HSC typically affects high-strength low alloy steels and carbon steels, particularly under tensile stress in a hydrogen-containing environment. This includes areas like weld-affected zones and hard spots in steels.

From API RP 571 Section 5.1.2.1 (Hydrogen-Induced Cracking):

"Hydrogen stress cracking (HSC) can occur in carbon steel and low alloy steels in environments containing hydrogen at ambient to moderately elevated temperatures (up to 200°F or 93°C)... Hardness is a critical factor for HSC. High hardness in welds and heat affected zones (HAZ) are most susceptible."

Additionally, API RP 939-C does not directly define HSC but reinforces the relationship between hydrogen exposure and metal integrity, particularly under conditions not exceeding 450 °F (230 °C) for hydrogen services.

Thus, option A is correct, as it directly reflects the metal types most susceptible to HSC in operational environments defined by API RP 571.

From API RP 571 and RP 932-B:

“In hydroprocessing reactor effluent systems, the most common corrosion mechanism is ammonium bisulfide (NH₄HS) corrosion, which forms in the presence of hydrogen sulfide and ammonia.”

“NH₄HS attacks carbon steel aggressively under turbulent flow and at low pH.”

Correct answer is B – ammonium bisulfide corrosion.

API RP 751 (referenced in RP 571) lists materials appropriate for HF acid alkylation service. It specifies:

“Chrome-moly steels such as ASTM A-193 B5 (5% Cr) bolts are preferred for their resistance to HF acid-induced cracking.”

“Standard low alloy steels (e.g., B7) are not considered adequately resistant.”

(Reference: API RP 571 summary & API RP 751, Section 5.6.3 – Bolting Materials)

Therefore, the correct and industry-approved answer is option A.