Pass the CWNP CWNA CWNA-109 Questions and answers with Dumpstech

 The cipher suite specified by the 802.11-2016 standard and is not deprecated is Counter Mode with CBC-MAC Protocol (CCMP). CCMP is an encryption protocol that uses Advanced Encryption Standard (AES) as the underlying cipher and provides confidentiality, integrity, and origin authentication for wireless data. CCMP is the mandatory encryption protocol for WPA2 and WPA3. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 295; [IEEE Standard for Information technology–Telecommunications and information exchange between systems Local and metropolitan area networks–Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications], page 1560.

A common feature of MDM solutions that can be used to protect enterprise data on mobile devices is containerization. Containerization is a technique that creates a separate and secure environment on the mobile device where enterprise data and applications are stored and accessed. Containerization isolates the enterprise data from the personal data and prevents unauthorized access, leakage, or loss of sensitive information. Containerization can also enforce security policies, encryption, authentication, and remote wipe on the enterprise data and applications. Over-the-air registration, onboarding, and self-registration are features of MDM solutions that facilitate the enrollment and management of mobile devices, but they do not directly protect enterprise data on mobile devices. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 336; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 326.

 The most effective method for testing roaming in relation to 802.11 VoIP handsets is to place a call with the handset and move around the facility to test quality during roaming. This method allows you to evaluate the actual performance and user experience of VoIP calls over wireless networks, as well as identify any potential issues such as signal strength, interference, latency, jitter, packet loss, or handoff delays. A spectrum analyzer can only show you the RF activity during a VoIP call, but not how it affects the voice quality or roaming behavior. A protocol analyzer can capture the traffic generated when a laptop roams, but it cannot simulate the characteristics of a VoIP handset such as battery life, antenna design, codec support, or QoS features. A built-in roaming monitor is not a common feature in all VoIP handsets, and it may not provide accurate or comprehensive information about the roaming process. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 487; [Voice over Wireless LAN 4.1 Design Guide], page 6-19.

802.11 QoS is achieved by giving high priority queues a statistical advantage at winning contention. 802.11 QoS is based on the Enhanced Distributed Channel Access (EDCA) mechanism, which defines four access categories (ACs) for different types of traffic: Voice, Video, Best Effort, and Background. Each AC has its own transmit queue and contention parameters, such as Arbitration Interframe Space (AIFS), Contention Window (CW), and Transmission Opportunity (TXOP). These parameters determine how long a station has to wait before transmitting a frame and how long it can occupy the channel. Higher priority ACs have shorter AIFS, smaller CW, and longer TXOP, which means they have more chances to access the channel and send more data than lower priority ACs. However, this does not guarantee that higher priority ACs will always win the contention, as there is still a random backoff process involved. Therefore, 802.11 QoS is a statistical service that provides different levels of service quality based on traffic categories. References: , Chapter 10, page 403; , Section 6.1

https://www.cablinginstall.com/articles/2012/08/cat-6a-vs-cat-5e-poe.html

The statement that the lowest voltage drop is achieved when using CAT6 cable instead of Cat5 or CAT5e is true about 802.3, Clause 33 Power over Ethernet. Power over Ethernet (PoE) is a technology that allows electrical power to be delivered over Ethernet cables along with data signals. PoE is defined by IEEE 802.3, Clause 33 and has several variants, such as PoE (802.3af), PoE+ (802.3at), and PoE++ (802.3bt). PoE works by using a device called PSE (Power Sourcing Equipment) that injects power into the Ethernet cable and a device called PD (Powered Device) that receives power from the Ethernet cable. The PSE can be either an endpoint device, such as a switch or a router, or a midspan device, such as an injector or a splitter, that is inserted between two Ethernet devices. The PD can be any device that requires power, such as an access point, a camera, or a phone.

One of the factors that affects PoE performance is voltage drop, which is the reduction of voltage that occurs as current flows through a cable due to its resistance. Voltage drop can cause power loss and inefficiency in PoE systems, as well as damage to PDs if the voltage falls below their minimum requirement. To minimize voltage drop, it is recommended to use high-quality cables with low resistance and short length. Among the common types of Ethernet cables, CAT6 has the lowest resistance and therefore the lowest voltage drop compared to Cat5 or CAT5e. CAT6 also has higher bandwidth and data rate than Cat5 or CAT5e, making it more suitable for PoE applications. References: 1, Chapter 7, page 263; 2, Section 4.4

A possible cause of a sudden change in performance for the laptop computers is that a new tenant in the building has set their AP to the same RF channel that your customer is using. This can create co-channel interference (CCI), which is a situation where two or more APs or devices use the same or overlapping channels in the same area. CCI can degrade the performance of WLANs by increasing contention, collisions, retransmissions, and latency. CCI can also reduce the effective range and throughput of WLANs by lowering the signal-to-noise ratio (SNR). To avoid or mitigate CCI, it is recommended to use non-overlapping channels, adjust transmit power levels, or implement channel management techniques such as dynamic frequency selection (DFS) or load balancing. The sky condition, antenna position, or Bluetooth headset are not likely to cause a sudden change in performance for the laptop computers. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 81; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 71.

Sensors should be deployed in critical areas where WLAN performance must be high for best results when using a WLAN monitoring solution that utilizes distributed sensor devices. A WLAN monitoring solution is a system that collects, analyzes, and reports on the status and performance of a WLAN. A WLAN monitoring solution can use different methods to gather data from the WLAN, such as embedded software agents, external hardware probes, or distributed sensor devices. Distributed sensor devices are dedicated devices that are deployed throughout the WLAN coverage area to monitor the wireless traffic and environment. Distributed sensor devices can perform various functions, such as scanning the spectrum, capturing wireless frames, measuring signal quality, detecting rogue access points, testing connectivity, and generating alerts. Distributed sensor devices can provide more accurate and comprehensive data than other methods, but they also require more planning and deployment costs. Therefore, it is important to deploy sensors strategically in critical areas where WLAN performance must be high, such as high-density zones, high-priority applications, or high-security locations. By deploying sensors in critical areas, the WLAN monitoring solution can ensure optimal WLAN performance and reliability in those areas and identify and resolve any issues or problems that may arise. The other options are not the best places to deploy sensors for best results. Deploying sensors in switching closets is not effective because sensors need to be close to the wireless medium to monitor it properly. Deploying sensors every 5 meters and alongside each AP is not efficient because sensors may overlap or interfere with each other and cause unnecessary redundancy or complexity. Deploying sensors above the plenum on each floor is not practical because sensors may not capture the wireless traffic and environment accurately due to attenuation or reflection from the ceiling materials or objects. References: CWNA-109 Study Guide, Chapter 14: Troubleshooting Wireless LANs, page 4831

The HT (802.11n) physical layer (PHY) specification includes support for and compatibility with both ERP and HR/DSSS. ERP stands for Extended Rate PHY, which is an extension of the original DSSS (Direct Sequence Spread Spectrum) PHY that supports data rates up to 54 Mbps in the 2.4 GHz band. HR/DSSS stands for High Rate/Direct Sequence Spread Spectrum, which is another extension of DSSS that supports data rates up to 11 Mbps in the 2.4 GHz band. HT stands for High Throughput, which is a new PHY that supports data rates up to 600 Mbps in both the 2.4 GHz and 5 GHz bands. HT uses OFDM (Orthogonal Frequency Division Multiplexing) as its modulation scheme, but it also supports legacy DSSS and ERP devices by using a dual preamble and header structure that allows backward compatibility. References: , Chapter 3, page 103; , Section 3.1

Shared Key Authentication is a security solution that was defined in the original 802.11 standard as an alternative to Open System Authentication, which does not provide any security at all. Shared Key Authentication uses WEP (Wired Equivalent Privacy) to encrypt and authenticate data frames between the client station and the AP. However, WEP has been proven to be extremely vulnerable to various attacks that can easily crack the encryption key and compromise the network security. Therefore, Shared Key Authentication is deprecated in the 802.11 standard and should never be used in any modern WLAN deployment . References: [CWNA-109 Study Guide], Chapter 10: Wireless LAN Security, page 401; [CWNA-109 Study Guide], Chapter 10: Wireless LAN Security, page 391; [Wikipedia], Wired Equivalent Privacy.

Passive Gain is the increase of RF energy in an intentional direction with the use of an antenna. It is achieved by focusing the same amount of power into a smaller area, resulting in a higher power density and a stronger signal. Passive Gain does not require any additional power or amplification, but rather depends on the antenna’s physical characteristics, such as size, shape, and orientation. Passive Gain is also expressed in decibels (dB) and is related to the antenna’s beamwidth and directivity. References: 1, Chapter 2, page 63; 2, Section 2.3