Pass the Huawei HCIP-Datacom H12-831_V1.0 Questions and answers with Dumpstech

A Layer 2 loop occurs when Ethernet frames circulate repeatedly through redundant switching paths without an effective loop-prevention mechanism.

Because Ethernet frames do not contain a TTL field equivalent to that used in IP packets, broadcast and unknown-unicast frames may continue circulating and multiplying.

This behaviour can create broadcast storms, causing excessive interface bandwidth utilization.

The resulting traffic volume can also overload the switch CPU, especially when large quantities of protocol or control packets are processed.

High CPU utilization can prevent administrators from logging in or cause the device to respond slowly to management operations.

Additionally, service interface indicators may blink unusually frequently because of the sustained traffic volume.

All four symptoms are consistent with Layer 2 loops. Huawei ' s troubleshooting documentation identifies these symptoms as indicators of switching loops.

Step 1: Understanding OSPF Areas and Summarization

Area 1 (NSSA - Not So Stubby Area)

Allows external routes but converts Type-5 LSAs into Type-7 LSAs.

External routes must be translated by an ABR into Type-5 LSAs before being propagated into other areas.

Area 2 (Common Area - Regular OSPF Area)

Supports both inter-area and external routes.

asbr-summary 10.0.4.0 255.255.255.0 Command

This command summarizes all external routes within 10.0.4.0/24 into a single summarized route.

Since it is applied on R1 and R3, these routers will advertise 10.0.4.0/24 instead of 10.0.4.4/32 to their respective areas.

Step 2: Route Distribution Analysis

R4 (Originating Router in NSSA - Area 1)

R4 injects 10.0.4.4/32 as a Type-7 LSA into Area 1.

R1 (ABR between Area 1 & Area 0, Summarizing Route)

Since R1 is an ABR, it translates Type-7 LSAs from Area 1 into a summarized Type-5 LSA (10.0.4.0/24) for Area 0.

✅ R1 has 10.0.4.0/24 in its routing table.

R2 (Inside Backbone Area 0, No ASBR Summary Applied Here)

R2 only receives Type-5 LSAs from R1 but does not summarize them.

Since R2 is not explicitly summarizing, it will likely still see 10.0.4.4/32 rather than 10.0.4.0/24.

❌ R2 does not have 10.0.4.0/24.

R3 (ABR between Area 0 & Area 2, Summarizing Route)

R3 is also an ABR and has the asbr-summary 10.0.4.0/24 command configured.

It will advertise the summarized route 10.0.4.0/24 into Area 2.

✅ R3 has 10.0.4.0/24 in its routing table.

R5 (Inside Area 2, No Direct Connectivity to External Routes)

Since R3 summarizes 10.0.4.0/24, R5 (inside Area 2) will receive only summarized routes.

✅ R5 has 10.0.4.0/24.

Final Answer: ✅ R1, R3 (Option A, C)

Comprehensive and Detailed In-Depth Explanation:

To determine the correct matches, we need to analyze VLAN aggregation and MUX VLAN behavior in the given topology.

1. Understanding VLAN Aggregation and MUX VLAN Roles

VLAN Aggregation:

Sub-VLANs (e.g., VLAN 10) are part of a Super-VLAN (e.g., VLAN 100) and share a common gateway.

Hosts in the same Sub-VLAN can communicate directly.

MUX VLAN (Multiple User Group VLAN):

Principal VLAN (VLAN 30): Includes servers, accessible by all VLAN types.

Separate VLAN (VLAN 20): Cannot communicate with other Separate VLAN hosts, but can communicate with the Principal VLAN (Server).

Group VLAN (VLAN 10 - Sub-VLANs): Hosts within the same Group VLAN can communicate, and they can also access the Principal VLAN (Server).

2. Analyzing the Connectivity

PC1 (Sub-VLAN 10 - Employee VLAN)

Can communicate with PC2 (same Sub-VLAN).

Can communicate with the Server (VLAN 30 - Principal VLAN).

PC2 (Sub-VLAN 10 - Employee VLAN)

Can communicate with PC1 (same Sub-VLAN).

Can communicate with the Server (VLAN 30 - Principal VLAN).

PC3 (VLAN 20 - Separate VLAN - Guest VLAN)

Cannot communicate with other PCs in Employee VLAN (PC1, PC2) or Guest VLAN (PC4).

Can communicate with the Server (VLAN 30 - Principal VLAN).

PC4 (VLAN 20 - Separate VLAN - Guest VLAN)

Cannot communicate with other PCs in Employee VLAN (PC1, PC2) or Guest VLAN (PC3).

Can communicate with the Server (VLAN 30 - Principal VLAN).

Server (VLAN 30 - Principal VLAN)

Can communicate with all PCs (PC1, PC2, PC3, PC4) because it belongs to the Principal VLAN, which serves all VLANs.

Huawei VRP requires MPLS and the Label Distribution Protocol (LDP) to be enabled at both the global and interface levels before dynamic label-switched paths can be established over an interface.

First, the mpls command enables the global MPLS function. Next, mpls ldp enables the global LDP process. These commands establish the necessary control-plane functionality.

At the interface level, mpls enables MPLS processing on GE0/0/1, and mpls ldp enables LDP neighbor discovery and label distribution through that interface.

All four commands are necessary in the configuration sequence shown in Huawei ' s training material. In a complete deployment, the administrator must also configure an appropriate MPLS LSR ID and ensure IP connectivity between neighboring devices.

Therefore, all four options are correct.

HCIP-Datacom-Advanced Routing & Switching Technology V1.0 Training Material.pdf

================

Comprehensive and Detailed In-Depth Explanation:

To determine which statements are false, we need to understand how OSPFv3 and IS-IS work together, and how Inter-Area-Router LSAs (Type 3 LSAs) are generated in OSPF:

1. Understanding OSPF Inter-Area LSAs (Type 3)

OSPF generates Type 3 LSAs (Inter-Area-Prefix LSAs) to advertise networks between areas.

Only Area Border Routers (ABRs) generate Inter-Area LSAs.

Type 3 LSAs allow routes to be advertised from one OSPF area to another (e.g., from Area 0 to Area 1 or Area 2).

2. Analysis of Each Answer Option:

✅ A. " R3 generates an Inter-Area-Router-LSA in Area 0. " → TRUE

R3 is an ABR (connecting IS-IS and OSPF Area 0).

Since R3 is importing IS-IS routes into OSPFv3, it must generate Type 3 LSAs to advertise those routes in Area 0.

This statement is correct.

✅ B. " R2 generates an Inter-Area-Router-LSA in Area 0. " → TRUE

R2 is also an ABR (connecting IS-IS and OSPF Area 0).

Like R3, R2 imports IS-IS routes into OSPFv3 and advertises them into Area 0 using Type 3 LSAs.

This statement is correct.

❌ C. " R1 generates an Inter-Area-Router-LSA in Area 2. " → FALSE

R1 is not an ABR.

Only ABRs generate Type 3 LSAs, and R1 is not an ABR between Area 2 and Area 0.

This statement is false.

❌ D. " R2 generates an Inter-Area-Router-LSA in Area 1. " → FALSE

Area 1 is a stub area, and stub areas do not allow Inter-Area-Router LSAs (Type 3 LSAs) for external routes.

R2 does not generate Inter-Area LSAs in Area 1 because OSPF prevents this in stub areas.

This statement is false.

Comprehensive and Detailed In-Depth Explanation:

Step 1: Analyzing the Primary Path

The given network uses IS-IS Auto FRR, which ensures a backup route in case of failure.

The shortest path from R1 to 10.0.3.3/32 is calculated based on the OSPF link costs:

Path 1 (Primary Path): R1 → R2 → R3

Cost: 10 (R1→R2) + 5 (R2→R3) = 15 ✅

Step 2: Checking the Backup Path

The statement claims that the backup path is R1 → R4 → R2 → R3. Let ' s calculate the cost:

Path 2 (Backup Path via R4): R1 → R4 → R2 → R3

Cost: 10 (R1→R4) + 50 (R4→R2) + 5 (R2→R3) = 65 ❌ (Too high)

The backup path should be an alternative shortest path that is as close as possible to the primary path in cost.

R1 → R4 → R2 → R3 is not a feasible backup path because the cost (65) is significantly higher than the primary path (15).

Step 3: Correct Backup Path Selection

If IS-IS Auto FRR is enabled, a feasible backup path should have a cost close to the primary path.

In this scenario, no viable alternative path meets the Auto FRR requirements efficiently.

The given backup path is incorrect.

Final Answer: ✅ FALSE (Option B)

Comprehensive and Detailed In-Depth Explanation:

The display startup command is used to check the startup and running configuration details of a Huawei network device.

It provides information on:✅ Running system software (currently active firmware).✅ Running configuration file (current settings in use).✅ Startup system software (firmware that will load on reboot).✅ Startup configuration file (configuration that will be applied on reboot).✅ Paths of these files in the storage system.

This command helps network administrators ensure that the correct firmware and configuration files are used when the device boots.

???? Reference: HCIP-Datacom Advanced Routing & Switching Technology – System Management and Configuration Files