Pass the HP ACMX HPE7-V01 Questions and answers with Dumpstech

The correct answer is B because HPE Alletra Storage MP B10000 supports VMware-oriented high-availability designs using Peer Persistence / Active Peer Persistence patterns. HPE documentation provides VMware ESXi host connectivity guidance for Alletra Storage MP B10000 and also describes VMware Metro Storage Cluster configurations with Active Peer Persistence. That is the correct platform positioning for protecting VMware workloads that require storage-level availability across sites. Option A is incorrect because Alletra 6000 Peer Persistence is based on NimbleOS synchronous replication behavior and is not positioned as an “Active Peer Persistence wizard with one-to-many topology.” Option C is also incorrect because Active Peer Persistence is a high-availability replication design, not a one-to-many replication topology. One-to-many replication is a different replication pattern and should not be conflated with Peer Persistence. Option D is incorrect because “Active Peer Persistence” is associated with Alletra Storage MP B10000 / Primera / Alletra 9000-class architecture rather than Alletra 6000’s classic Peer Persistence model. Reference/topics: HPE Alletra Storage MP B10000, VMware ESXi integration, Active Peer Persistence, storage HA design.

The correct answer is A. HPE Zerto is the appropriate solution because the requirements describe application and VM-level cyber resilience/disaster recovery, not array management or backup-target hardware. Zerto protects virtualized workloads using near-synchronous, block-level replication and journal-based recovery, which supports very low RPOs and granular recovery points. HPE’s Zerto product material describes near-synchronous replication with recovery points measured in seconds, and HPE GreenLake for Disaster Recovery uses Zerto continuous data protection in a cloud-service model. Option B is incorrect because HPE Data Ops Manager manages HPE block storage operations and data services; it is not the DR engine for cross-hypervisor workload replication. Option C is a storage-server platform and does not provide the requested VM-level replication service. Option D, HPE StoreOnce, is a backup appliance target; it is valuable for backup retention and deduplication but does not provide near-synchronous, block-level VM replication across hypervisors. Reference/topics: HPE Zerto, HPE GreenLake for Disaster Recovery, VMware workload protection, pay-per-use data protection, block-level replication.

The correct answer is C. The exhibit shows an HPE Alletra Storage MP B10000 configuration based on QLC flash, with raw capacity below the customer’s 450 TB target. The correct capacity adjustment is to increase the number of QLC drives in the system while selecting the sparing policy that maximizes available usable capacity for the intended design. Replacing QLC with TLC is not the right direction for a high-capacity all-flash requirement because QLC media is positioned for dense, cost-efficient capacity expansion. Adding host bus adapters does not increase raw storage capacity, so option A is unrelated to the requirement. Replacing controller nodes is also unnecessary because the problem is media capacity, not controller performance. HPE Alletra Storage MP B10000 QuickSpecs identify scale-out capacity characteristics, including maximum raw capacity per shelf, confirming that the platform is intended to scale capacity through shelves and drive population rather than by changing host-connectivity cards. The correct plan is to add QLC capacity to reach the raw-capacity target and adjust sparing appropriately. Reference/topics: B10000 capacity planning, QLC all-flash sizing, sparing policy, GreenLake proposal validation.

The correct answer is A because VXLAN/EVPN data-center fabrics are normally built on a routed Layer 3 underlay. In this design, each top-of-rack switch forms independent routed links toward the core or spine layer, and equal-cost multipath routing is used to provide scale-out bandwidth and resilience. The VXLAN/EVPN overlay then provides Layer 2 and Layer 3 tenant connectivity above that routed underlay. Option B is incorrect because LAG member Layer 2 ports represent a traditional Layer 2 aggregation design, not the preferred underlay model for EVPN/VXLAN. Option C is also incorrect because standalone Layer 2 links would create an underlay that lacks the routed ECMP characteristics expected in this fabric architecture. Option D is not the best answer because LAG is not required between TOR and core switches in an EVPN routed fabric; independent routed links provide better fabric behavior and failure isolation. The course includes Aruba networking and advanced virtualization/data-center design topics, and this question tests the candidate’s ability to select the correct port model for an HPE Aruba EVPN/VXLAN solution.

The correct answer is D because the requirement is not simply additional raw capacity; it is a write-performance target of 500K IOP/s. For HPE Alletra Storage MP B10000 designs, controller-node model selection, node count, shelf count, drive population, and media layout collectively determine whether the configuration can satisfy the performance envelope. Merely increasing the number of drives, as suggested in option C, does not guarantee that the front-end controller resources, CPU, cache, and back-end connectivity can sustain the required write workload. Options A and B use lower or inappropriate node selections for this stated requirement. The B10230 model, combined with additional shelf and drive resources, is the configuration change that aligns the controller and media resources with the required write I/O target. HPE’s course outline places HPE Alletra Storage MP B10000 in both general enterprise solution design and database workload solution design, which is exactly the kind of workload-sensitive sizing exercise represented here. The proposal must be validated against the customer’s required I/O profile, not only against usable capacity.