Pass the Huawei HCSP Presales H19-404_V1.0 Questions and answers with Dumpstech

Huawei SD-WAN provides all four technologies. Per-flow load balancing distributes separate application flows among multiple links that have the same priority and satisfy the required SLA. Per-packet load balancing can transmit packets from one flow across multiple eligible links, improving aggregate bandwidth utilization for large file transfers, backups, and replication.

Multi-fed and selective receiving duplicates critical traffic across different links. The receiving device selects valid packets, removes duplicates, and preserves packet order. Packet loss or failure on one path therefore does not interrupt the service, enabling zero-millisecond link switchover in applicable deployments.

A-FEC dynamically generates redundant packets and adjusts the redundancy ratio according to measured packet loss. The receiving device reconstructs lost packets, reducing video freezing and voice-quality deterioration. Huawei describes both adaptive FEC and multi-fed selective receiving as WAN-optimization mechanisms for key traffic.

Intelligent traffic steering selects links according to application identity, quality, bandwidth, priority, and load. Therefore, A, B, C, and D are all correct.

==================

A terminal-type survey primarily determines the appropriate network admission control solution. Different terminal categories have different authentication capabilities and security requirements. Corporate laptops may support 802.1X authentication, guests may require Portal authentication, and printers, cameras, sensors, and other dumb terminals commonly require MAC-address authentication or automatic terminal identification.

Huawei recommends selecting authentication technologies according to the terminal type and usage scenario. For example, access switches can serve as authentication points for wired dumb terminals, while APs or other access devices can perform authentication for wireless users. After terminal identification is enabled, iMaster NCE-Campus can automatically assign VLANs, ACLs, security groups, QoS parameters, and other authorization policies according to terminal category.

The survey therefore establishes which endpoints support interactive authentication, which require non-interactive admission, and which must receive special isolation or compliance policies. It does not independently determine the complete physical network architecture or the overall O & M platform. Consequently, the terminal survey is used to formulate the network admission control solution, making option C correct.

==================

PROFINET DCP, meaning Discovery and Basic Configuration Protocol, is used during device discovery and initial network configuration. It operates at the data-link layer and enables an engineering station or PROFINET IO controller to locate devices on the local Ethernet segment, identify them by MAC address or station name, assign a PROFINET device name, and configure IP parameters such as the IP address, subnet mask, and default gateway.

DCP is therefore not responsible for normal cyclic process-data exchange. Real-time PROFINET communication performs that function after the controller and I/O device have been configured and an application relationship has been established. Alarm exchange and acyclic parameterization are also handled through other PROFINET communication relationships and services.

The distinction matters during commissioning. A new I/O device may initially have no usable IP configuration. DCP allows the controller or engineering tool to discover it at Layer 2 and provision the identity and addressing information required before higher-layer communication can begin. PROFINET documentation identifies DCP as mandatory for assigning IP addresses and configuring station names on the local network.

==================

A network serving 15,000 wireless terminals is a large-scale WLAN and should use a standalone WAC solution. A dedicated WAC provides independent controller resources, scalable AP and user management, centralized WLAN policy control, and the ability to deploy controller redundancy without tying wireless-control capacity directly to a specific core-switch service card.

Huawei recommends a standalone WAC when the wireless network scale is large or when the wireless network is deployed independently over an existing wired campus. The WAC is typically connected to the aggregation or core layer in off-path mode, and VRRP hot standby can be used to improve reliability.

Native WAC solutions are valuable for unified wired and wireless management, authentication, forwarding, and policy enforcement. However, for a very large number of wireless terminals, the controller platform must be selected according to user, AP, traffic, and forwarding-capacity specifications. A standalone WAC allows the wireless control plane to be sized and expanded independently.

Option C provides the dedicated WAC together with the required core and aggregation or access infrastructure. Therefore, it is the recommended architecture for 15,000 wireless terminals.

WIPS is the correct technology because it provides wireless intrusion prevention capabilities, including detecting and containing rogue access points, rogue stations, ad hoc devices, spoofing attempts, flood attacks, and other malicious activity on the radio interface. Huawei’s security-design material groups WIDS and WIPS with wireless attack detection and rogue-device containment. It recommends attack detection in public areas and primary or secondary education environments with high security requirements.

WIDS primarily detects and reports suspicious behavior, while WIPS adds active prevention or containment actions according to the configured policy. The other options serve different purposes. Mesh is a wireless networking architecture used to provide backhaul connectivity or extend coverage between APs; it is not an attack-detection mechanism. Spectrum analysis identifies non-Wi-Fi interference sources and evaluates radio-frequency utilization, but does not provide complete security attack detection and containment. Protected Management Frames protects selected 802.11 management frames against forgery, deauthentication, and disassociation attacks, but it is a protection mechanism rather than the comprehensive detection system requested. Therefore, WIPS is the correct answer.

==================

APs support barcode scanning through the CloudCampus APP, DHCP Option 148–based deployment, and deployment through Huawei’s registration query center. With barcode scanning, the installer scans the AP’s label using the CloudCampus APP. The application obtains information such as the electronic serial number and MAC address, associates the AP with the correct tenant and site, and allows the AP to register with iMaster NCE.

With DHCP Option 148, the DHCP server supplies the AP with its IP configuration and the IP address and port number of iMaster NCE. The AP changes to cloud-management mode and automatically initiates registration. Huawei lists AR routers, switches, and APs as supported devices for this mode.

The registration query center can also provide the controller address after the AP contacts Huawei’s query service. It supports APs together with ARs, firewalls, and switches. Email-based deployment is primarily an SD-WAN CPE or AR-router ZTP method, not an AP deployment mode. Therefore, A, C, and D are correct.

==================

After identifying a terminal, iMaster NCE-Campus can use the identification result for security monitoring, visibility, and policy automation. Spoofing detection is supported because the platform can compare a terminal’s current type and traffic behavior with its previously identified characteristics. For example, if a device originally identified as an IP phone suddenly behaves like a PC, the system can generate a spoofing alarm or apply an isolation policy.

Terminal identification also supports statistics and reporting by vendor, operating system, device category, access port, and policy status. Huawei explicitly describes terminal-type statistics, report export, and visibility of access policies.

In addition, iMaster NCE-Campus can automatically deliver VLAN, security-group, QoS, authentication, and access-permission policies according to the identified terminal type. Option B is incorrect because wired authentication is an admission process, not a service produced after terminal identification. Therefore, A, C, and D are correct.

==================

The AR5710-S8T1XWE-NRGL supports all four listed 5G-Advanced capabilities. Support for 3GPP Release 16 enables enhanced 5G New Radio functions and provides the standards foundation for improved mobile-WAN capacity, reliability, and service performance.

Carrier aggregation combines multiple component carriers to increase available throughput. Downlink 3CC allows three component carriers to be aggregated for received traffic, while uplink 2CC combines two carriers for transmitted traffic. This is valuable for high-bandwidth branch access, video backhaul, and mobile private-network scenarios.

Support for eight APNs permits multiple logically separated mobile services or provider profiles to be configured. Different APNs can represent enterprise services, management traffic, production systems, backup connectivity, or isolated customer networks. Global-frequency-band support improves deployment flexibility across countries and carrier networks, subject to local spectrum regulation and the supported modem variant.

Huawei SD-WAN can use 5G as a primary, secondary, or bypass link and supports combinations such as dual 5G and 5G plus wired connectivity for service assurance. Therefore, NR Release 16, carrier aggregation, eight APNs, and global frequency bands are all supported.

==================

WAPI, or WLAN Authentication and Privacy Infrastructure, is the wireless LAN security standard proposed by China. It provides wireless link authentication and data-protection mechanisms and was developed as an alternative security framework for WLAN environments. Huawei’s training material explicitly identifies WAPI as a WLAN security standard proposed in China and states that it provides stronger protection than legacy WEP and WPA mechanisms.

WPA, WPA2, and WPA3 belong to the Wi-Fi Protected Access family maintained through Wi-Fi industry certification. WPA was introduced as an interim improvement over WEP. WPA2 adopted stronger IEEE 802.11i security mechanisms, including AES-based CCMP. WPA3 later introduced stronger password-authentication and enterprise-security options.

WAPI incorporates authentication and encryption as part of an integrated wireless security architecture. Its deployment depends on regional requirements, terminal compatibility, AP support, and the organization’s regulatory or cryptographic-policy obligations. The question asks which standard originated as a Chinese wireless security standard, not which standard is most widely deployed internationally. Therefore, WAPI is the only correct choice, making option B the verified answer.

==================

Huawei firewalls provide four commonly predefined security zones: Local, Trust, DMZ, and Untrust. The Local zone represents the firewall itself, including traffic generated by or destined for the device, and has the highest default security priority of 100. The Trust zone normally represents an organization’s protected internal network and has a default priority of 85, not 95. Therefore, option C is false.

The DMZ typically hosts public-facing or semi-trusted resources, such as web, email, and application servers. Its default priority is 50, placing it between the trusted internal network and the external untrusted network. The Untrust zone normally represents the Internet or another uncontrolled network and has the lowest predefined priority of 5.

Zone priority expresses the relative security level used to classify inbound and outbound traffic direction; it does not independently permit traffic. Security policies still determine whether matched traffic is allowed or denied. Huawei’s SD-WAN design uses Trust and Untrust zones on CPEs, and iMaster NCE can orchestrate the corresponding zones and firewall policies for Internet-access protection.

==================