Pass the Juniper JNCIS-MistAI JN0-460 Questions and answers with Dumpstech

According to Juniper Networks' EVPN-VXLAN documentation, devices that perform the encapsulation and de-encapsulation of Ethernet frames into VXLAN UDP packets at the edge of the network are known as Virtual Tunnel Endpoints (VTEPs)1111. In the context of a campus fabric overlay, these devices often function as L2 gateways when they bridge traditional Layer 2 traffic from end-user devices across a Layer 3 IP fabric.

The exhibit demonstrates a 3-stage IP Clos architecture where access1 and access3 are explicitly identified as VTEP endpoints. A VXLAN tunnel is shown originating at access1 and terminating at access3, allowing "User1" and "Server1"—both located on the same 10.1.1.0/24 subnet—to communicate as if they were on the same physical Layer 2 segment despite being separated by a Layer 3 IP Fabric (172.16.0.0/24). In this scenario, access1 and access3 fulfill the L2 gateway role by mapping the local VLAN traffic to a specific VXLAN Network Identifier (VNI) for transport across the underlay3.

As L2 gateways, these switches maintain the bridge table for the overlay network, learning MAC addresses from local ports and via the EVPN control plane from remote VTEPs4. This architecture allows for seamless Layer 2 mobility and connectivity across complex routed infrastructures while eliminating the need for Spanning Tree Protocol (STP) in the core5555. In contrast, options like "VNI" refer to the segment ID itself rather than a device role, and "root bridge" refers to an STP-specific role that EVPN-VXLAN is designed to move away from in a modern fabric.

AMarvis Actions Missing VLANnotification indicates that anaccess pointis missing a VLAN configured on other APs within the same site.

Marvis identifies configuration inconsistencies by comparing VLAN assignments across devices.

Wired AssurancedefinesSLEs (Service Level Expectations)to provide measurable performance indicators for wired networks. These metrics identify root causes of network degradation by monitoring switch health, connection success, and throughput performance.

“Juniper Mist Wired Assurance delivers AI-driven insights across key wired SLEs including Successful Connects, Throughput, and Switch Health, giving visibility into user experience and switch performance.”

Option A (Capacity):Incorrect — capacity is used in wireless SLEs, not wired.

Option B (Successful Connects):Correct— tracks connection success rate and anomalies.

Option C (Switch Health):Correct— monitors hardware, software, and PoE status.

Option D (Coverage):Incorrect — pertains to wireless SLEs.

Option E (Throughput):Correct— measures data transfer rate, latency, jitter, and loss.

Juniper Mist defines both3-stageand5-stage IP Closarchitectures for campus and data-center fabrics. The5-stage IP Closdesign adds scalability by introducingspineandsuper-spinelayers above the leaf layer, enabling large campus or aggregation environments.

“The 5-stage IP Clos topology extends the 3-stage design by introducing spine and super-spine tiers. It is ideal for large campus environments requiring additional capacity and hierarchical scaling.”

Option A:Incorrect — Clos is a topology, not a routing protocol.

Option B:Incorrect — VXLAN/EVPN encapsulation operates over Clos but does not define it.

Option C:Incorrect — that describes a traditional three-tier campus (core/distribution/access), not a Clos.

Option D:Correct— the5-stage IP Closis a hierarchical, scalable Clos topology withspine and super-spinelayers used in large campus or data-center networks.

Aport negotiation mismatchoccurs when the local and remote interfaces fail to agree on common speed or duplex settings.

Marvis Wired Assurance automatically detects this by analyzing telemetry from the switch’s physical interfaces.

You can resolve this by ensuringauto-negotiationis enabled on both ends (A) and verifying the peer device supports the802.3 autonegotiation standard(D).

Manually forcing half-duplex or replacing hardware is unnecessary unless the hardware is faulty.

“Marvis Wired Actions correlate interface negotiation errors with LLDP neighbor data to pinpoint mismatched configurations, helping administrators quickly verify speed/duplex compatibility and 802.3 autonegotiation support.”