Black Friday VIP Hour Limited Time 75% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = simple75

Pass the Netapp NAHSE NS0-094 Questions and answers with Dumpstech

Exam NS0-094 Premium Access

View all detail and faqs for the NS0-094 exam

Practice at least 50% of the questions to maximize your chances of passing.
Viewing page 2 out of 3 pages
Viewing questions 11-20 out of questions
Questions # 11:

What are two valid options for uploading a core file from a node that is running ONTAP 9.12.1 software to NetApp for analysis? (Choose two.)

Options:

A.

system node autosupport invoke -diagnostic

B.

Download via CIFS and upload to upload.netapp.com.

C.

Download via Service Processor Infrastructure (SPI) and upload to upload.netapp.com.

D.

system node autosupport invoke-core-upload

Questions # 12:

You are upgrading your 6-node NetApp ONTAP cluster from ONTAP 9.9.1 to 9.16.1. As part of the ONTAP software upgrade process, you need to update the cluster switches. After you update the first switch, you receive the following AutoSupport message:

Exhibit — AutoSupport Alert

vifmgr: callhome.clus.net.degraded:alert:

Call home for CLUSTER NETWORK DEGRADED:

Large MTU Packet Loss - Ping failures detected

between Node1_clus1 (169.254.2.94) on Node1

and Node2_clus2 (169.254.248.67) on Node2.

All cluster ports and interfaces are in an up/up status.

What is causing this error?

Options:

A.

ONTAP software is not at the same version on all nodes.

B.

The RCF file has not been applied to all switches.

C.

The ONTAP software version is not compatible with some of the controllers.

D.

The cluster switches have different firmware versions.

Questions # 13:

You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.

What are two possible causes? (Choose two.)

Options:

A.

The SAS cables were incorrectly reconnected after reinstalling the motherboard.

B.

The disks that are owned by this node have been marked as failed.

C.

The node is booting a lower version of ONTAP software than was last used.

D.

The interconnect is down.

Questions # 14:

When you plan an ONTAP upgrade, which NetApp tool generates a detailed upgrade plan?

Options:

A.

ONTAP System Manager

B.

Active IQ Unified Manager

C.

Upgrade Advisor

D.

Active IQ Config Avisor

Questions # 15:

Which three commands can be used to manually generate a kernel core file? (Choose three.)

Options:

A.

SP > system power cycle

B.

:: > reboot –node < node_name > –dump true

C.

:: > halt –dump true –node < node_name >

D.

:: > system node panic –node < node_name >

E.

SP > system core

Questions # 16:

Which RAID type provides protection against three disk failures?

Options:

A.

RAID DP

B.

RAID-TEC

C.

RAID 5

D.

RAID 4

Questions # 17:

In preparation for an upgrade to ONTAP 9.6P8 software, you have uploaded the ONTAP image 96P8_q_nodar_image.tgz onto your local web server with address 192.168.10.10.

Which is correct command syntax to download this image to the cluster image repository?

Options:

A.

ClusterA:: > storage firmware download –node local –package-url

http://192.168.10.10/96P8_q_nodar_image.tgz

B.

SP ClusterA–01 > cluster image package get –url

http://192.168.10.10/96P8_q_nodar_image.tgz

C.

ClusterA:: > cluster image package get –url

http://192.168.10.10/96P8_q_nodar_image.tgz

D.

ClusterA:: > cluster image package get –url

http: //netapp.com/ontap9/downloads/96P8_q_nodar_image.tgz

Questions # 18:

During which two operations is the NVRAM replayed by the high-availability (HA) partner? (Choose two.)

Options:

A.

after triggering a sync core

B.

when a node is halted

C.

during a negotiated takeover

D.

when the node loses power

Questions # 19:

A customer replaced a data switch, and NetApp ONTAP software is showing the following output:

Question # 19

Why is the port shown as degraded after creating the VLAN?

Options:

A.

The port is not a member of the failover group for this VLAN.

B.

The interface group (ifgroup) is configured as active/standby.

C.

The VLAN is not configured on the connected data switch port.

D.

The connected data switch port is in a shutdown state.

Questions # 20:

What are two valid commands that can be used to trigger an AutoSupport? (Choose two.)

Options:

A.

:: > autosupport history show-upload-details –node < nodename >

B.

:: > system node coredump upload –node < nodename >

C.

:: > autosupport invoke –node < nodename > –type all

D.

:: > autosupport invoke-core-upload –node < nodename >

Viewing page 2 out of 3 pages
Viewing questions 11-20 out of questions