Pass the Checkpoint CCSE 156-315.82 Questions and answers with Dumpstech

The correct answer isC. A Poor score in the Compliance Blade means the administrator must investigate the failed Security Best Practices and take corrective action where appropriate. The Compliance Blade uses Continuous Compliance Monitoring to examine gateways, blades, policies, and configuration settings against regulatory standards and Check Point security best practices. It also suggests corrective measures when deficiencies are found. Option A is bad administration; deactivating poor practices hides the problem instead of correcting it. Option B is impossible because the administrator does not simply mark a failed best practice as Good. Option D is fabricated; there is no general “Copilot will configure everything” correction workflow in the official Compliance Blade behavior. The correct operational response is to analyze, review, and remediate.

========

The correct answer isB. In R82 SmartConsole Central Deployment, up to10 target installationscan run at the same time. The R82 Security Management Administration Guide states that an administrator can select up to 30 Security Gateways and Cluster Members, but only 10 installations can take place concurrently; all other targets are placed in a queue and processed as earlier installations finish. This applies to Central Deployment operations for Hotfixes, Jumbo Hotfix Accumulators, and Upgrade Packages. Option A is wrong because three is not the R82 SmartConsole Central Deployment concurrency limit. Option C is also wrong because five is below the documented limit. Option D is wrong because SmartConsole Central Deployment is explicitly intended for batch deployment, not one-at-a-time operation. The operational detail is important: the administrator may select a large group of gateways, but the Management Server enforces the parallel execution limit. For the exam, the direct number is10 concurrent installations. Reference topic:Central Deployment in SmartConsole / Installation Concurrency.

========

The correct answer isB. Check Point’s R82 ElasticXL important notes state that an ElasticXL Cluster supports a maximum ofthree ElasticXL Cluster Members on each ElasticXL Siteandsix ElasticXL Cluster Members in total. Six total members with three per site means a maximum of two sites. Option A is wrong because three sites would imply up to nine members, which exceeds the six-member total. Option C is wrong because it limits each site to two members and permits three sites, which is not the documented ElasticXL structure. Option D is wrong because four members per site is unsupported. The architecture is therefore clear: ElasticXL scales up to three members in a site and supports a second site for HA-style topology, for a maximum total of six members. If more members are required, Check Point documentation explicitly directs administrators to use Maestro instead. Reference topic:ElasticXL Important Notes / Supported members and sites.

========

The correct answer isA. In the R81/R82 policy installation architecture, the policy installation request is handled first by theCPMprocess on the Management Server side. CPM is the core Check Point Management process responsible for modern management database operations and policy installation coordination. After CPM receives and processes the install request, the installation flow can involve FWM for verification, conversion, code generation, and compilation depending on whether a Modern Dump or Legacy Dump path is used. Option C is attractive because FWM is absolutely involved in the policy installation flow, especially for verification/conversion and legacy processing, but the question asks which Management Server process receives the install command. That makesCPMthe better answer. Option B is incorrect because CPWD is a watchdog process used to monitor and restart Check Point daemons, not the install-command handler. Option D is incorrect because FWD is a Security Gateway/logging-side daemon, not the Management Server process that receives policy installation requests. Reference topic:Policy Installation Flow / CPM and FWM roles.

========

The correct answer isC. In a Management High Availability environment, thePrimary Security Management Servermust be upgraded first. Check Point’s R82 Installation and Upgrade Guide is explicit: before upgrading other servers in Management HA, make sure the Primary Security Management Server is upgraded and running. The procedure then lists step 1 as upgrading the Primary Security Management Server with one of the supported methods, such as CPUSE, Advanced Upgrade, or Migration, and step 2 as upgrading the Secondary Security Management Server. This sequencing protects the management database authority and avoids creating a situation where secondary systems are upgraded before the primary management role is stable. Option A is wrong because Dedicated Log Servers follow the management upgrade strategy and must match compatibility requirements afterward. Option B is wrong because Secondary Management is not first. Option D is wrong because Security Gateways are upgraded after the Management Servers that control them. Reference topic:Upgrading Security Management Servers in Management High Availability from R80.20 and higher.

========

The correct answer isD. Management HA synchronization is controlled from the Management High Availability configuration area under Global Properties, not from the object properties of the Primary Management Server. Check Point’s Management HA configuration guidance identifies the Global Properties Management High Availability window as the place where synchronization behavior is defined. This aligns with the architecture: synchronization is an environment-level management property, not a property of only one Management Server object. Option A is wrong because editing the Primary SMS object is used for object-level configuration, not for the HA synchronization schedule. Option B is wrong because automatic synchronization does exist; the Active Management Server synchronizes Standby servers at intervals and when sessions are published. Option C is also too absolute because synchronization behavior is configurable through the management properties. For exam precision, distinguish betweenmonitoring/changeover, which is done from SmartConsole Menu > Management High Availability, andsynchronization timing configuration, which belongs under Global Properties. Reference topic:Management High Availability / Synchronization Configuration.

========

The correct answer isC. In R81 and higher, Check Point policy installation logic distinguishes betweenLegacy DumpandModern Dump. This distinction is part of the newer policy installation architecture, where some policy data can be prepared in a modern, optimized format instead of passing through the older legacy flow. Legacy Dump follows the traditional path where policy data requires verification, conversion, code generation, and compilation before being transferred to the Security Gateway. Modern Dump is the optimized path where policy data is prepared with pre-generated code and does not require the same additional compilation or verification stage before transfer. Option A is wrong because CPD and CPM are daemons/processes, not the two database dump types. Option B invents a “Monitoring Dump” category that is not part of policy installation terminology. Option D is also wrong because FWD is a gateway/logging-related daemon and AUM is not one of the database dump types. Reference topic:Policy Installation Flow / Legacy Dump and Modern Dump.

========

The correct answer isD. Each ElasticXL Cluster Member requires at leastfour interfaces. Check Point’s R82 ElasticXL documentation states that an ElasticXL Cluster requires at least four interfaces on each member: a dedicated management interface, a dedicated Sync interface, an external interface, and an internal interface. The Mgmt port is selected automatically for the management interface, and the Sync port is selected automatically for the synchronization interface. The administrator selects and configures the external and internal data interfaces. Option A and Option B overstate the requirement. Option C is wrong because three interfaces would not satisfy the documented minimum: management, synchronization, external, and internal are all required as separate functional interface roles. This is not a design preference; it is an ElasticXL requirement. For CCSE R82, the answer is straightforward:minimum four interfaces per ElasticXL Cluster Member. Reference topic:ElasticXL Important Notes / Minimum interface requirement.

========