Pass the Cisco CCNP Wireless 300-110 Questions and answers with Dumpstech

Cisco Application Visibility and Control (AVC) is a deep packet inspection and traffic classification framework integrated into the Cisco WLC and AP platform. AVC performs real-time analysis of wireless client traffic, classifying applications based on Layer 4-7 signatures using the NBAR2 (Network Based Application Recognition) engine. This provides the network administrator with granular visibility into exactly which applications are consuming bandwidth — enabling data-driven decisions about network congestion remediation, link utilization management, and infrastructure investment planning. For example, AVC can reveal that a video streaming application is consuming 60% of available wireless bandwidth during peak hours, informing the decision to implement QoS rate limiting for that application class or upgrade the backhaul infrastructure. AVC also supports control functions through per-application QoS policies, rate limiting, and traffic shaping — directly addressing congestion reduction. Band selection (Option A) steers dual-band clients to 5 GHz but provides no application-level analysis. QoS (Option B) implements traffic prioritization but requires prior application identification — it does not perform the analysis itself. 802.11r (Option D) is a fast roaming protocol with no relevance to traffic analysis or congestion management. Reference: WLSD Study Guide — Application Visibility and Control, NBAR2 Integration, Wireless Traffic Analysis and Management.

This multi-constraint design scenario requires precise alignment of EWC architecture, N+1 redundancy hierarchy, AAA integration, and WLAN security policies. Option B correctly addresses all requirements. With only three APs per branch and a requirement to keep traffic local, converting a single C9130 to EWC mode is the correct and resource-efficient approach — converting two APs to EWC (Options A and C) wastes AP capacity in a small three-AP branch. The preferred controller set to the EWC AP ensures local APs join locally. The HQ WLC as primary N+1 backup satisfies the data center WLC always being primary requirement. Other branches ' EWC APs configured as secondary and tertiary controllers creates the cross-branch redundancy hierarchy. Since guests and employees share the same SSID but require different VLANs, MAC Authentication Bypass (MAB) with AAA override allows the HQ ISE/AAA server to return VLAN attributes based on device or user identity — dynamically assigning the correct VLAN at the policy level. The 2 Mbps guest rate limiting is applied through per-client QoS policies on the EWC. Option D ' s use of local web auth for guests does not enable dynamic VLAN assignment from AAA. Reference: WLSD Study Guide — EWC Architecture, N+1 Redundancy Hierarchy, AAA Override and Dynamic VLAN Assignment.

In Ekahau Site Survey, when planning a warehouse deployment using patch (directional) antennas, the antenna downtilt setting is the critical adjustment made when placing simulated APs on the floor plan map. Patch antennas have a defined radiation pattern with a main lobe that must be aimed precisely at the intended coverage zone. In a warehouse environment, APs with patch antennas are typically wall-mounted and aimed down aisles. The downtilt angle determines the vertical component of the antenna ' s aim — adjusting the downtilt in Ekahau tilts the simulated antenna ' s main radiation lobe downward toward the warehouse floor and the working zone of RF scanner devices, rather than projecting RF energy horizontally at an ineffective angle. Ekahau allows engineers to specify the horizontal and vertical orientation of the antenna in three dimensions, and the downtilt value directly controls how the software models the antenna ' s coverage pattern in the vertical plane. AP channel (Option A) is set during channel planning, not during AP placement. Wi-Fi technology (Option B) determines the modulation and protocol standard but is set as an AP property. AP transmission power (Option D) controls cell radius but is set separately from antenna orientation. Reference: WLSD Study Guide — Ekahau Predictive Survey, Directional Antenna Configuration, Warehouse RF Design and Antenna Orientation.

In Ekahau Site Survey, passive mode involves listening to beacon frames and probe responses from deployed APs without the survey laptop actively associating to any SSID. This is significantly faster than active mode because no association, DHCP, or throughput test overhead is introduced — the surveyor simply walks the floor while Ekahau passively captures signal strength data from all visible APs simultaneously. Using two wireless adapters in passive mode provides a critical speed advantage: one adapter scans 2.4 GHz channels while the second adapter simultaneously scans 5 GHz channels. Without dual adapters, a single adapter must time-multiplex between bands, reducing the sample rate per band and either slowing the survey walk or producing sparser data. Active mode (Options B and C) is used when throughput measurements are required for specific application validation such as voice or video, but it is inherently slower due to association overhead and sequential testing. The combination of passive scanning and dual adapter configuration delivers the highest possible data collection rate per unit of walk time. Reference: WLSD Study Guide — Ekahau Site Survey Modes, Passive vs. Active Survey Methodology, Multi-Adapter Survey Configuration.

Raising the minimum data rate to 24 Mbps reduces the effective coverage range of each AP because clients at the cell edge operating at low data rates are effectively excluded from the cell. This shrinks cell size, reducing channel overlap between neighboring APs on the same channel. Using directional antennas limits the coverage area of some APs by focusing RF energy in specific directions rather than radiating omnidirectionally, which directly reduces the lateral overlap between adjacent APs. Increasing AP transmit power (Option B) would worsen overlap, not reduce it. Allowing UNII-2e channels (Option C) provides more channel options but does not reduce the physical cell overlap — it only provides more channels to avoid co-channel interference. Power saving mode (Option E) is a client-side power management feature unrelated to AP cell sizing during a survey. Reference: WLSD Study Guide — Channel Overlap Mitigation, Data Rate Configuration, Directional Antenna Use Cases.

This question hinges on a fundamental network engineering constraint: the maximum transmission distance of copper Ethernet cabling. IEEE 802.3 standards specify a maximum segment length of 100 meters (328 feet) for all standard PoE and Ethernet over Category 5e, 6, or 6A UTP copper cabling. The parking lot light poles are approximately 200 meters from the closest wiring closet — more than double the maximum copper distance. This immediately eliminates Options A and D, which specify Category 6 UTP cabling: at 200 meters, UTP copper cannot reliably carry Ethernet at any supported speed, and PoE cannot be delivered over this distance regardless of standard. The correct solution is fiber optic connectivity between the wiring closet and the parking lot, combined with a local AC/DC power module at each pole location. Fiber optic cabling supports single-mode runs of kilometers and multi-mode runs of hundreds of meters at Gigabit speeds — easily spanning 200 meters. At the AP mounting location on the light pole, an AC/DC power module (powered from the pole ' s existing electrical supply) converts AC power to the DC power the AP requires. Option B (fiber with 802.3af) is incorrect because PoE cannot be delivered over fiber — 802.3af requires copper cabling for simultaneous power and data delivery. Reference: WLSD Study Guide — Outdoor AP Deployment, Fiber vs. Copper Distance Limitations, Outdoor Power Solutions.

Cisco WLC AP Failover Priority governs the order in which APs are processed when a WLC recovers and APs begin re-associating. The priority levels are: Critical, High, Medium, and Low. During recovery situations, the WLC will accept and process AP join requests in order of priority — Critical priority APs are processed first, before all other priority levels. In a deployment where the WLC is located in a remote data center connected via WAN, the join process for all APs is slower due to WAN latency and potential bandwidth constraints. Under these conditions, assigning Critical priority to executive office APs ensures they are at the front of the processing queue and restore service before lower-priority APs. The executive office designation implies business-critical operations requiring the fastest possible wireless restoration — a requirement that directly maps to the Critical priority level. High priority (Option A) would position the executive APs second in the queue behind any Critical priority APs. Medium (Option B) and Low (Option C) would place them further down the processing order. Reference: WLSD Study Guide — AP Failover Priority Configuration, N+1 and SSO Redundancy Design, WAN-Linked Controller Deployments.

The command ' debug mobility handoff enable ' is used to validate the mobility control packets between Wireless LAN Controllers (WLCs). This command enables debugging of the handoff process, which is critical for ensuring seamless client roaming between controllers. When WLCs are separated by firewalls, it is essential to confirm that mobility control packets can traverse these firewalls without being dropped or rejected. The ' debug mobility handoff enable ' command allows network administrators to monitor the handoff process in real time and identify whether mobility PDUs are being exchanged successfully. If mobility control packets are being blocked by the firewall, this debug output will show failures in the handoff sequence. This command directly validates bidirectional mobility traffic flow, making it the correct troubleshooting tool for the scenario described. Options A and D are not valid Cisco WLC commands. Option C enables configuration-level mobility debugging but does not specifically validate handoff packet flow. Reference: WLSD Study Guide — Mobility Troubleshooting, Debug Commands, Inter-Controller Roaming Validation.

The Cisco WLAN site survey methodology follows a structured, sequential process. The initial walkthrough — sometimes called the discovery or orientation phase — is the first step, during which the engineer physically tours the facility to understand its physical characteristics: building materials, structural layout, potential AP mounting locations, wiring closet positions, and environmental factors. After completing the initial walkthrough, the next logical phase is the predeployment survey (also referred to as a pre-deployment or predictive survey). The predeployment survey uses the information gathered during the walkthrough to create a detailed design plan — either through a manual AP placement plan or a predictive survey tool such as Ekahau, where floor plans are annotated with materials and attenuation values and APs are virtually placed to model coverage. The predeployment survey output is the design document that drives the actual physical installation. A post-deployment survey (Option A) validates coverage after installation — it cannot precede deployment. Active and passive surveys (Options B and D) are physical measurement techniques conducted either pre-deployment (with temporary APs) or post-deployment (with installed APs) — they do not logically follow immediately after a walkthrough before any design work is done. Reference: WLSD Study Guide — WLAN Site Survey Process, Predeployment Survey Phase, Airport Wireless Design Considerations.

Enabling AP fallback globally on the WLC allows access points to reconnect to their primary controller after they have connected to a secondary controller due to the primary being offline. This is the exact behavior described in the scenario — APs successfully fail over to the secondary WLC but do not return to the primary WLC when it recovers. AP Fallback is a WLC-level setting that monitors the availability of each AP ' s configured primary controller and initiates a reconnection when the primary becomes reachable again. Without AP Fallback enabled, APs remain on whatever controller they most recently joined — in this case, the secondary — even after the primary recovers. The CAPWAP AP Controller IP Address command (Option A) permanently changes the primary controller configuration on the AP, which is not the intended solution — the AP already has the correct primary configured. DHCP Option 43 (Option B) is used for initial AP discovery, not fallback. AP Failover Priority (Option D) controls which APs are processed first during a failover event, not whether APs return to their primary controller. Reference: WLSD Study Guide — AP Fallback Configuration, N+1 Redundancy Recovery, Controller Primary/Secondary Hierarchy.