Spring Sale Limited Time 75% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = simple75

Pass the Cisco CCNP Enterprise 300-410 Questions and answers with Dumpstech

Exam 300-410 Premium Access

View all detail and faqs for the 300-410 exam

Go to Exam

Practice at least 50% of the questions to maximize your chances of passing.

Viewing page 10 out of 13 pages

Viewing questions 136-150 out of questions

Questions # 136:

Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

Options:

shared risk link group-disjoint

linecard-disjoint

lowest-repair-path-metric

interface-disjoint

Questions # 137:

Refer to the exhibit.

Question # 137

Which configuration configures a policy on R1 to forward any traffic that is sourced from

the 192.168.130.0/24 network to R2?

Question # 137

Options:

Option A

Option B

Option C

Option D

Questions # 138:

Refer to the exhibit.

Question # 138

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the

configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

Options:

Use an extended access list instead of a standard access list.

Change sequence 10 in the route-map command from permit to deny.

Use a prefix list instead of an access list in the route map.

Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Questions # 139:

Refer to the exhibit.

Question # 139

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?

Options:

Add the aaa authentication login default none command to the global configuration.

Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command.

Add the aaa authentication login default group tacacs+ local-case command to the globalconfiguration.

Add the login authentication Console command to the line configuration

Questions # 140:

Refer to the exhibit.

Question # 140

An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?

Options:

no ip ssh disable

ip ssh enable

ip ssh version 2

crypto key generate rsa

Questions # 141:

Which option is the best for protecting CPU utilization on a device?

Options:

fragmentation

COPP

ICMP redirects

ICMP unreachable messages

Questions # 142:

Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

Options:

Router ospf3 1 address-family ipv4

Router(config-router)#ospfv3 1 ipv4 area 0

Router(config-if)#ospfv3 1 ipv4 area 0

Router ospfv3 1 address-family ipv4 unicast

Questions # 143:

While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?

Options:

The device must be resynced to Cisco DNA Center.

The software image for the device is in install mode.

The device has lost connectivity to Cisco DNA Center.

The software image for the device is in bundle mode

Questions # 144:

Refer to the exhibit.

Question # 144

Which routes from OSPF process 5 are redistributed into EIGRP?

Options:

E1 and E2 subnets matching access list TO-OSPF

E1 and E2 subnets matching prefix list TO-OSPF

only E2 subnets matching access list TO-OSPF

only E1 subnets matching prefix listTO-OS1

Questions # 145:

A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

Options:

service timestamps log uptime

clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00

service timestamps log datetime localtime show-timezone

clock calendar-valid

Questions # 146:

Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?

Options:

multi-paths eibgp 2

maximum-paths 2

Maximum-paths ibgp 2

multi-paths 2

Questions # 147:

What is a limitation of IPv6 RA Guard?

Options:

It is not supported in hardware when TCAM is programmed

It does not offer protection in environments where IPv6 traffic is tunneled.

It cannot be configured on a switch port interface in the ingress direction

Packets that are dropped by IPv6 RA Guard cannot be spanned

Questions # 148:

Refer to the exhibit.

Question # 148

The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host

192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action

resolves the issue without opening full access to this router?

Options:

Move the SSH entry to the beginning of the ACL

Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow works

Temporarily remove the ACL from the interface to see if the flow works

Run the show access-list FILTER command to view if the SSH entry has any hit statistic associated with it

Questions # 149:

Refer to the exhibit.

Question # 149

In which circumstance does the BGP neighbor remain in the idle condition?

Options:

if prefixes are not received from the BGP peer

if prefixes reach the maximum limit

if a prefix list is applied on the inbound direction

if prefixes exceed the maximum limit

Questions # 150:

Which two statements about VRF-Lite configurations are true? (Choose two.)

Options:

They support the exchange of MPLS labels

Different customers can have overlapping IP addresses on different VPNs

They support a maximum of 512.000 routes

Each customer has its own dedicated TCAM resources

Each customer has its own private routing table.

They support IS-IS

Viewing page 10 out of 13 pages

Viewing questions 136-150 out of questions