Pass the Cisco CCNP Data Center 300-615 Questions and answers with Dumpstech

The correct action is Replace the cable with a transceiver between the fabric interconnect and the switch. Cisco UCS troubleshooting depends on the relationship between policy, inventory discovery, firmware state, and server identity. The question involves UCS, firmware, fabric interconnect, so the selected option fixes the UCS component or policy that directly controls the failure. In UCS Manager, service profiles, vNIC/vHBA templates, boot policies, firmware packages, server pools, adapters, fabric interconnects, and I/O modules are applied through a managed model; a server can fail even when basic IP reachability exists if the relevant policy is incomplete or the hardware inventory has not been acknowledged correctly. The distractors typically change an unrelated object, force a disruptive recovery without fixing the policy, or apply to a different UCS mode. Cisco guidance is to verify faults, FSM stage, inventory status, association status, and the specific boot or connectivity policy before taking action. After the remediation, validate that the fault clears, the FSM completes, and the server or fabric component returns to the expected operable state.

The answer is Roll back to the original image because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references FEX; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer-gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post-change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.

/workspace/backup inside fabric interconnect is the appropriate UCS remediation because the symptom maps to a specific managed object rather than a generic server failure. Cisco UCS abstracts hardware through service profiles and policies; therefore, issues involving UCS, firmware, fabric interconnect must be corrected where UCS Manager programs the adapter, boot target, firmware, management certificate, pool qualification, or fabric interconnect state. The selected answer restores that programming path. The other options may appear plausible, but they do not correct the object that UCS uses to derive operational state. For example, boot failures require the correct vHBA/iSCSI target and LUN policy, discovery issues require the proper physical and management path, and firmware failures require the documented recovery action for the failed FSM stage. The correct validation is to inspect the associated fault, confirm inventory acknowledgment, verify the policy under the service profile or equipment tree, and then recheck boot or connectivity behavior after the FSM completes.

Cisco troubleshooting logic supports EVPN Type 1-5 as the required fix. In this question the symptoms point to EVPN, and the defect is best handled by correcting the exact control-plane or consistency condition. Nexus platforms can show interfaces or peers as configured while still refusing to forward traffic if a vPC Type-1 parameter, VLAN allowance, MTU, HSRP version, EVPN route, or routing attribute is wrong. Cisco methodology is to avoid broad resets unless the state machine is stuck; instead, correct the mismatched parameter and verify that the resulting operational state becomes stable. The other choices do not remove the root cause, or they modify a setting that is not used by the failing protocol exchange. After the change, the engineer should review the peer status, route or MAC table, and counters for drops or inconsistency messages. That sequence proves that the network fabric is fixed, not merely restarted.

The selected resolution is VSAN 1 is suspended because the failure is in the Fibre Channel/FCoE control path around MDS, VSAN, Cisco Nexus. Cisco MDS and Nexus platforms separate configuration from operational state: a VSAN, zone, vFC binding, device alias, or port-security entry can exist in configuration but still fail if it is not active, correctly merged, or allowed on the link. The correct option addresses the fabric condition that prevents communication. The incorrect options are technically adjacent but would not repair the specific dependency; for example, changing unrelated databases or resetting ports without correcting policy leaves the same failure to recur. Cisco SAN troubleshooting therefore starts with port role and VSAN checks, then confirms fabric services such as fcdomain, FSPF, zoning, fabric binding, and name-server information. The expected validation is that the port becomes operational, the initiator and target appear in the appropriate databases, and permitted zone members can communicate.

Change operation type to POST resolves the problem because the symptom is specific to the automation subsystem handling APIC, Postman. Nexus automation failures are frequently caused by a missing EEM event statement, absent event-default action, invalid REST path, incorrect JSON or XML syntax, Guest Shell DNS/resource settings, or a scheduler feature that is not enabled. The selected answer corrects that execution prerequisite. The wrong options may make sense for normal switch forwarding, but they do not repair the automation control path. Cisco documentation treats Guest Shell as a separate Linux environment and EEM as a policy engine that can intercept CLI events; both must be validated from their own operational state. A proper verification is to confirm the policy is registered, run the job or API call again, review the response or syslog output, and ensure that normal CLI behavior is preserved after the automation fires.

The correct answer is Enable LLDP on the neighbor switch. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on VSAN, FCoE, DCBX, LLDP, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.

The answer is Enable LLDP because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references DCBX, LLDP, Cisco Nexus; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer-gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post-change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.

Cisco troubleshooting logic supports Resolve unicast reply from Router R2 as the required fix. In this question the symptoms point to OSPF, and the defect is best handled by correcting the exact control-plane or consistency condition. Nexus platforms can show interfaces or peers as configured while still refusing to forward traffic if a vPC Type-1 parameter, VLAN allowance, MTU, HSRP version, EVPN route, or routing attribute is wrong. Cisco methodology is to avoid broad resets unless the state machine is stuck; instead, correct the mismatched parameter and verify that the resulting operational state becomes stable. The other choices do not remove the root cause, or they modify a setting that is not used by the failing protocol exchange. After the change, the engineer should review the peer status, route or MAC table, and counters for drops or inconsistency messages. That sequence proves that the network fabric is fixed, not merely restarted.

The selected action, Use a browser that supports keys of 2048 bits, is the proper operational fix. The scenario points to ACI, APIC, certificate, which means the issue is controlled by management policy, role mapping, service state, certificate handling, or firmware lifecycle rather than normal packet forwarding. Cisco documentation separates these domains: a device may ping another device, but UCS Central registration, LDAP/RADIUS authorization, APIC security-domain access, SNMP access, or browser trust still fails if the required management attribute is wrong. The selected answer aligns the configuration with the management workflow. The other answers either address unrelated connectivity or provide a workaround that does not satisfy the platform requirement. Verification should be explicit: authenticate as the affected user, confirm the returned role or domain, check fault status, and validate that the management task completes without warnings. That proves the operational plane is corrected.