Pass the Cisco CCNP Service Provider 350-501 Questions and answers with Dumpstech

How does model-driven telemetry use YANG?

Refer to the exhibit. An engineer working for a private telecommunication company with an employee id: 3414:81:713 is implementing this network, in which:

Routers R1A and R1B are eBGP neighbors.

iBGP is configured within AS 65515 and AS 65516.

Network 192.168.2.0/24 is shared with AS 65516.

Router R3A has an iBGP relationship with router R2A only.

Router R2A has an iBGP relationship with routers R1A and R3A.

Which additional task must the engineer perform to complete the configuration?

An organization with big data requirements is implementing NETCONF as part of its migration to a new cloud-based environment. The organization has multiple offices across widespread geography. A network engineer is configuring NETCONF on one of the border routers. Which configuration must the engineer apply to save the running configuration?

Drag and drop the characteristics from the left onto the automation tool on the right.

Refer to the exhibit. Users on a LAN that is connected to RD communicate to multiple servers on the corporate network. Initially, the servers were located on the same LAN. However, after congestion was reported, the engineering team decided to relocate the servers to two different networks.

Which task should the team perform to improve performance on the overall network while still allowing traffic to flow between the different hosts?

Guidelines

-

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

-

Configure and verify the OSPF neighbor adjacency between R1 and R2 in OSPF area 0 according to the topology to achieve these goals:

1. Establish R1 and R2 OSPF adjacency. All interfaces must be advertised in OSPF by using the OSPF interface command method. Use Loopback0 as the OSPF ID.

2. There must be no DR/BDR elections in OSPF Area 0 when establishing the neighbor relationship between R1 and R2. OSPF must not generate the host entries /32 for the adjacent interfaces.

3. Enable OSPF MD5 Authentication between both routers at the interface level with password C1sc0!.

Which type of attack is an application attack?

A network engineer has configured TE tunnels in the MPLS provider core. Which two steps ensure traffic traverse? (Choose two.)

Refer to the exhibit. Tier 1 ISP A is connected to small Tier 3 ISP B. The EBGP routing protocol is used for route exchange. The networking team at ISP A noticed the flapping of BGP sessions with ISP B. The team decides to Improve stability on the network by suppressing the subnet for 30 minutes when a session begins to flap. Which action must the team perform to meet this goal?

Refer to the exhibit. A large enterprise has multiple branch offices that span several geographic regions. The enterprise runs MPLS within the core to propagate VPNv4 routes using BGP. After a recent series of DDoS attacks disrupted the network, a network engineer has been asked to reconfigure BGP to help mitigate future attacks. Which configuration must the engineer apply?

A)

B)

C)

D)

Refer to the exhibit.

Which two topology changes happen to the IS-IS routers? (Choose two.)

Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right.

Refer to the exhibit. The enterprise is running BGP between sites to provide connectivity to users across the company's geographic regions. A network engineer must update the configuration so that the operations team can confirm that BGP prefixes that are received on each router originated from the correct autonomous system.

Which configuration must the engineer apply?

A mod-size service provider uses L2VPN as its standard for connectivity between offices. A small company wants the service provider to connect the company’s two sites across the service provider core. To meet service requirements, the service provider must extend the layer 2 domain between the company’s two locations. Which configuration must the engineer apply to implement an attachment circuit between the two sites using a VLAN tag of 12?

Refer to the exhibit.

An engineer ran this show telemetry command to view subscription SUB11 on RouterX. The engineer then decided that RouterY should provide the same output lor sensor group SGroup13 as RouterX. The engineer cannot access RouterX to copy its configuration No access lists on the router block user access Which configuration must the engineer apply on RouterY to provide the same output from the show telemetry command?

A)

B)

C)

D)