Pass the Cisco CCNP Service Provider 350-501 Questions and answers with Dumpstech

 Enabling MPLS LDP IGP Synchronization ensures that the IGP advertises a route only if there is a corresponding label binding from LDP. This synchronization helps prevent blackholing traffic when there is a direct link failure in the network. When the B-C link failed, the IGP could find an alternate path via routers E and F, but without LDP synchronization, the labels for MPLS were not available on this new path, leading to traffic loss. By enabling LDP IGP Synchronization, routers will only use paths for which a complete set of labels exists, ensuring label forwarding occurs on the alternate path.

 The configuration shown in the exhibit indicates a BGP FlowSpec policy that is configured locally on CSR1. This policy is designed to drop all traffic destined for TCP ports 80 and 443 for the IP address 10.6.5.0/24. The traffic rate is displayed as 0 bps, which suggests that the policy is not currently dropping any traffic. However, the matched and dropped statistics indicate that the policy has been active in the past, as it has matched and dropped packets.

To implement Bidirectional Forwarding Detection (BFD) in an IS-IS environment, the first task is to configure BFD in an interface configuration mode. This involves setting up BFD parameters on the interfaces where IS-IS is running to enable quick failure detection.

The issue of no LDP neighbor existing for 1.1.1.1 between two directly connected routers could be due to R2 not receiving any hellos from R1. In the context of LDP (Label Distribution Protocol), hellos are used for the discovery of LDP peers. They are sent periodically on each interface that LDP is enabled on to discover and maintain LDP sessions with neighbors. If R2 is not seeing any hellos from R1, it means there’s a failure in the initial step of establishing an LDP session, hence no neighbor relationship is formed.

 The control plane protocol used between Cisco SD-WAN routers and vSmart controllers is the Overlay Management Protocol (OMP). OMP is a proprietary protocol of Cisco SD-WAN that facilitates the exchange of routing, policy, and management information across the network. It operates within the secure environment provided by the Datagram Transport Layer Security (DTLS) or Transport Layer Security (TLS) control connection, ensuring that the communication between the routers and controllers is encrypted and authenticated1.

References := Cisco 300-415: Cisco SD-WAN vSmart-WAN Edge Router Control Plane Protocol

The OSPF adjacency issue between R1 and R2 is likely due to mismatched OSPF network types or hello/dead interval settings. The command ip ospf network point-to-point is used on point-to-point network types, which do not require matching hello/dead intervals, thus allowing OSPF adjacency to form even if these intervals are mismatched on the two routers. References: = Implementing and Operating Cisco Service Provider Network Core Technologies course materials. (

The configuration in Option A is correct for enabling dial-out telemetry streams using gRPC on devices with TLS disabled.

It uses model-driven telemetry (MDT), which is a new method of monitoring network devices. Unlike traditional methods that pull data from the device, MDT pushes data from the device to the collector.

In this configuration:

Telemetry is model-driven.

It specifies a destination group with an IP address and port number where the telemetry data will be sent.

The encoding is self-describing-gpb (Google Protocol Buffers).

The protocol used is TCP.

This setup ensures that telemetry data is sent to the specified collector without requiring TLS encryption.

 The Network Services Orchestrator (NSO) is designed to allow service providers to automate network operations efficiently. It provides a single, well-defined API that enables integration across various network environments. NSO’s capabilities include zero-touch telemetry, machine learning intuition, open APIs, and automated actions, which facilitate a simpler and more efficient network operation experience. This makes it an ideal choice for service providers looking to plan, optimize, and achieve closed-loop operations within their networks.

References := The information is based on the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) training and certification resources, which offer a deep dive into service provider technologies, including core architecture, services, networking, automation, quality of services, security, and network assurance123.

IOS XE:

It uses linux-based kernel

It has a separate control plane

IOS:

It is monolithic

It shares memory space

In Option A, the configuration correctly classifies and marks management protocols with DSCP AF23, which belongs to AF class 2 with low drop probability.

Monitoring protocols are marked with DSCP AF13, aligning with AF class 1 and low drop probability.

All other traffic is marked with a DSCP value of 0, as required.