Pass the ISTQB Foundation Level ISTQB-CTFL Questions and answers with Dumpstech

Comprehensive and Detailed In-Depth Explanation:

Static testing (A) applies to non-executable work products (I), such as requirements or code reviews. It also leads to defect detection (III) and finds defects directly (IV) without executing the software. Options B, C, and D incorrectly associate static testing with performance measurement (II) or dynamic testing aspects (V).

Good traceability between the test basis and test work products provides several advantages: i. Analyzing the impact of changes: Traceability allows for easy identification of which parts of the test work products will be affected by changes in the requirements or design, facilitating impact analysis. iv. Making testing auditable: Traceability ensures that there is a clear connection between the requirements and the test cases, which makes the testing process auditable and provides evidence that all requirements have been tested​​.

The question is about marking the correct sentences among the given statements related to defects, failures, and mistakes. According to the ISTQB glossary, the definitions of these terms are1:

Defect: A flaw in a component or system that can cause the component or system to fail to perform its required function, e.g. an incorrect statement or data definition. A defect, if encountered during execution, may cause a failure of the component or system.

Failure: An event in which a component or system does not perform a required function within specified limits.

Mistake: A human action that produces an incorrect result.

Therefore, out of the five given statements, only two are correct, namely:

A human mistake may produce a defect: This is true, as a mistake is a source or cause of a defect, e.g. a programmer may make a mistake in writing a code statement, which results in a defect in the software component.

When a defect exists in a system it may result in a failure: This is true, as a defect is a potential or actual cause of a failure, e.g. a defect in the software component may cause the system to fail to perform a required function when the defect is encountered during execution.

The other three statements are incorrect, namely:

Defects are a result of environmental conditions and are also referred to as “Failures”: This is false, as defects are not a result of environmental conditions, but of mistakes or other factors, and defects are not the same as failures, but rather the causes of failures.

A system will totally fail to operate correctly when a failure exists in it: This is false, as a system may not necessarily fail completely or stop operating when a failure occurs, but may continue to operate with reduced functionality or performance, or with incorrect results.

Defects occur only as a result of technology changes: This is false, as defects can occur due to various reasons, not only technology changes, such as human mistakes, design flaws, requirement changes, hardware failures, etc.

All testing levels are applicable, independent of which software development life-cycle process (V-model, iterative, incremental) is used. Testing levels are defined based on the scope and objectives of testing, not on the software development model. Component testing, integration testing, system testing and acceptance testing are common testing levels that can be applied to any software development model, as long as they are planned and executed properly. The V-model is a software development model that emphasizes the relationship between each development phase and its corresponding testing phase. Iterative and incremental models are software development models that divide the development process into smaller cycles or iterations, where each iteration produces a working version of the software that can be tested and evaluated. Verified References: A Study Guide to the ISTQB® Foundation Level 2018 Syllabus - Springer, page 18.

Cost can be regarded as an exit criterion for testing, because it is a factor that affects the profitability and feasibility of the software product. Testing is an investment that aims to improve the quality and reliability of the software product, but it also consumes resources, such as time, money, and human effort. Therefore, testing should be planned and executed in a way that balances the cost and benefit of testing activities. Having cost as an exit criterion helps to avoid spending too much money on testing, which may result in an unprofitable product or a loss of competitive advantage. Cost can also help to prioritize and focus the testing efforts on the most critical and valuable features and functions of the software product. However, cost should not be the only exit criterion for testing, as it may not reflect the true quality and risk level of the software product. Other exit criteria, such as defect rate, test coverage, user satisfaction, etc., should also be considered and defined in the test plan.

The other options are incorrect, because they either deny the importance of cost as an exit criterion, or they make false or unrealistic assumptions about the cost of testing. Option B is incorrect, because the financial value of product quality can be estimated, for example, by using cost-benefit analysis, return on investment, or cost of quality models. Option C is incorrect, because going by cost as an exit criterion does not necessarily constrain the testing project or help achieve the desired quality level. Cost is a relative and variable factor that depends on the scope, complexity, and context of the software product and the testing project. Option D is incorrect, because the cost of testing can be measured effectively, for example, by using metrics, such as test effort, test resources, test tools, test environment, etc.

Covering all transitions at least once is the highest coverage criterion for state transition based test cases, because it ensures that every possible change of state is tested at least once. This means that all the events that trigger the transitions, as well as the actions and outputs that result from the transitions, are verified. Covering all transitions at least once also implies covering all states at least once, but not vice versa. Therefore, option D is not the highest coverage criterion. Option C is the lowest coverage criterion, because it only tests the initial and final states of the system or component, without checking the intermediate states or transitions. Option A is incorrect, because the coverage criteria for state transition based test cases can be determined and compared based on the number of transitions and states covered. References = CTFL 4.0 Syllabus, Section 4.2.3, page 49-50.

This answer is correct because Behavior-Driven Development (BDD) is a test-first approach, where tests that express a shared understanding from stakeholders of how the application is expected to work, are first written in business-readable language (following the Given/When/Then format), and then made executable to drive development. BDD is a collaborative approach that involves testers, developers, business analysts, product owners, and other stakeholders in defining the expected behavior of the application using scenarios that describe the preconditions, actions, and outcomes of the application. BDD scenarios are written using a domain-specific language (DSL) that can be translated into executable test cases using tools such as Cucumber or SpecFlow. BDD aims to improve communication, collaboration, and feedback among the team members, and to deliver software that meets the customer’s needs and expectations. References: ISTQB Glossary of Testing Terms v4.0, ISTQB Foundation Level Syllabus v4.0, Section 3.1.1.4

, Requirements Engineering Fundamentals.

The minimum number of test cases needed to cover every unique sequence of up to 3 states/2 transitions starting in the “Start” state and ending in the “End” state is 4. This is because there are 4 unique sequences of up to 3 states/2 transitions starting in the “Start” state and ending in the “End” state:

Start -> Bet -> End

Start -> Deal -> End

Start -> 1st Deal -> End

Start -> 2nd Deal -> End References: ISTQB Certified Tester Foundation Level (CTFL) v4.0 sources and documents.

State transition testing is a black-box testing technique used to analyze the behavior of a system by examining the transitions between different states in response to events. In state transition testing, a state table or diagram is used to represent the states of a system and the transitions between these states triggered by events.

Option D is correct because in state transition testing, all transitions between states should be explicitly shown in the state table. This includes valid transitions that the system is expected to make under normal operation and, where relevant, invalid transitions that should be tested to ensure the system handles unexpected or erroneous inputs gracefully. The state table provides a comprehensive view of how the system should behave, making it possible to create tests that cover all defined transitions.